remote start doesnt work

Question

Function C1 programmed. 38.1 and 2.1 programmed. but  remote start doesnt work.

Answer 1

Here is the programming for the ftx remotes and the Evo-One

Comments

Step 5 no flash lights confirmation. On evo-one red light on. What's wrong.

---

Does the red led under the yellow loop blink once when pressing the brake pedal at step 4?

If not this would indicate an issue with your brake wire connection...I would verify this first...

Also ensure that the module is not in valet mode...

---

4FR9-ZPFE-YAFE-EEKC can you activate this code one more time. Need to check brake wire one more time

---

Once a code is put in it cannot be re activated. It is only good for 48 hours.

However here is what the brake wire should be... white connector left of fuse box it is the blue wire #78 in the picture this is positive brake wire...Test this wire is should show 0v when the brake is not pressed and 12v when brake pedal is pressed...

---

Wire connection is good. 12v when press brake. Trying to activate master reset.Doesn't work.Trying to programm remotes, step 4 lights flashing once. Step 5 still no confirm. Doesn't work.

---

Red light still flashing on evo-one. Not on the near yellow loop.

---

Were did you plug in your atenna?

---

Antenna plugged on black 4 pin slot near programm button. When i plug blue light flashing couple times.

---

Red battery +12v. Black ground. Black pin-evo-one. Blue pin antenna.

---

The antenna has to be plugged into the smaller of the 2 blue ports on the evo-one. It will not work plugged into the black 4 pin plug.

Plug it into the small blue 4 pin plug and program the remotes...Let me know what happens.

---

It work. Remotes programmed. When i press start button ingnition goes on but engine not starting. Parking lights blinking. After couple seconds goes of. After 5-10 seconds same things.

---

please count the number of parking light flashes when the vehicle stops trying to start.

 

Thank you,

---

You need to set option 20 mode 2 in the remote starter. You have it set to mode 1 right now.

Also you set lock after start on both the bypass and remote starter...You need to turn one of them off you can have options over lapping eachother.

---

4 times flash. Pause around 3-5 seconds. 10 times flash

---

Turn ignition on press valet switch 3 times turn ignition off...Then ensure you have correct your tachless setting and try to remote start the vehicle.

---

Doesn't work anyway. After 4 tames flash. One second pause. 4-5 time flash. Ignition goes of. Engine not starting.

---

This is telling you it is in valet mode...Take the module out of valet mode as previously mentioned.

Also you have not set it to the correct tachless setting as previously mentioned.

---

Heres the park light flash codes.

---

This is how to enter/exit valet mode

---

Red light under yellow loop blinking when i press star.

---

Better to call us as it seems you need more help...

Toll Free: 1-877-336-7797

---

The gyu from technical support said switch to function 2 mode. Wires reconnected. Still same. Please help.

---

Function 4 mode 2. Sorry

---

Function 2 mode 4. Sorry

---

Please tell me. It's possible to start toyota tacoma 2007 with evo-one and rf641w or not. Remotes programmed. Trying to start. But won't start. Lock/unlock doesn't work. What's wrong?

---

Absolutely will!!

Did you connect the lock and unlock wires in the vehicle? These have to be connected for locks to function. purple on the 20 pin connector is the lock wire and purple/white is the unlock wire from the 20 pin connector. These need to be connected to the negative lock and unlock wires in this truck. As the guide states the evo one only does immobilizer bypass....

If the vehicle is not starting then something is wrong with either the programming of the module and options or the way it has been installed.

---

I use guide #22971connection 1programm1. There is purple and purple/white not connected. If you have any other guide, i will be happy to see it.

---

Please help me. When i press strart button on remote: parking lights flashing 4 times, 1 sec pause, 5 times flashes. Engine won't crank.

---

The lock wires are not shown because we only show the immobilizer portion of the install. You need to connect the purple and purple/white wires for lock and unlock in the vehicle for it to work as I previously mentioned.

Looked at your service number again and in the Bypass section you have turned off some options that will definitely prevent the truck from starting. Turn on options A1 to A11. and re program the module in the vehicle.

---

Have a question about wires location. Where is  A8 (-) GWR, A4 (-) ignition, A6 (-) disarm and A5 (-) start on toyota tacoma 2007

---

Lock/unlock doesn't work. Purple and purple/white connected to purple, green/black. Double puls programmed. Remote start working. Thanks for guys from technical support. For tacoma program 2 mode 4 required. When remote started flashing parking lights every time. What's wrong. Thanks

Answer 2

we do not support 3x lock  start on the 2007 Toyota Tacoma. The feature is not listed on fortin.ca for this vehicle. https://fortin.ca/en/vehicles/toyota/tacoma/2007/

 

An rf-kit is needed.

Comments

So. Will it work on tacoma 2007 with rf641w?

---

100% compatible

---

Ok. so set of Evo-one + rf641w is 100% remote start for toyota tacoma 2007.

---

yes that will work 100%

---

Have received rf641w kit. No guide for evo-one. Need to know how to programm remote transmitter on evo-one.

---

find Evo-one on product page and then click on "docs & guides" and look for the search bar that says "all devices" and select "RF Kit" from there you should be able to find which remotes you are using