Questions & Answers

evo-chrt4 dodge charger 2008 red light only

–1 vote
when i connect the device to the using the T-harness then i insert the 4 pin data link while holding the button it is only giving a red light.

 

second then which connection type should i use for my car
asked Jan 22, 2015 in Dodge by zaid sasa (160 points)

1 Answer

0 votes
 
Best answer
Can you provide us with the service number for your Evo-All.

And the connection guide depends on how you are going to use the Evo-All in the vehicle, (with Remote starter through datalink, with Remote starter WITHOUT datalink, or Stand Alone)
answered Jan 22, 2015 by Jesus Monroy (63,860 points)
selected Jan 23, 2015 by Robert T
Service number: 001A06 429137

I don't know what are the difference between them and I don't know if their is a build in remote starter in my car

are you trying to do 3x lock start (connection C) ? The options for this setup are not enabled in your unit right now : http://fortin.ca/en/support/001a06429137/

when i connect the device to the using the T-harness then i insert the 4 pin data link while holding the button it is only giving a red light.

For the programming in the car, make sure the dark blue wire from the 20-pin connector of the EVO is not connected anywhere. Also make sure the yellow/black wire of the EVO is not connected anywhere.

 

I want to do a 3x lock start that's why I bought this chip , but option c is not enabled what option I can use in my case . Becouse I bought this device to fit my car
you will need to turn on certain options on the Evo-All by using a Flashlink-2 updater and Flashlink Manager v3.52 to be able to use 3x lock.
Yesterday i recieved the flash-link-updater 2 and i enabled option D1 and D2.

Step two i linked the yellow wire in the 20 pin to the yellow wire that come from the T-harness.

Step Three i cut the yellow wire from the female harness and link it to yellow/green in the 5 pin red.

Then i start programing.

What happend is that when i trun the ignition to on mode it start blinking in blue ,after i remove the key and click on the lock button. it is still binking but slowly with the blue color.

What i am missing ???

Hellllllllllllllllp is needed

Do a master reset,

 

Push and hold the programming button, insert datalink cable, release on RED, push and hold programming button again until the 3 colored leds flash one after another.

 

Go back to the computer, enable option C1, D1, and D2

 

Go back to the vehicle,

1. Hold the programming button, insert datalink,, release on BLUE

2.Turn Ignition key to ON/RUN postion, led should flash BLUE

3. Since you already enabled D2 to ON, skip this step

3Turn the Igntion to OFF

4. BLUE led shoud flash rapidly

5. PRESS the LOCK button on the OEM remote

6. BLUE led should turn OFF

Thank you and i will try it today.
I did everything you told me , but after i connect the 4 connectors to the evo-all and trun the key to on/run it is not blinking anymore , please advise.

"Step Three i cut the yellow wire from the female harness and link it to yellow/green in the 5 pin red."

 

 

I reread your comments and saw this, please make sure that the YELLOW  from the MALE side of the t-harness is connected to the YELLOW/GREEN of the RED 5 pin connector

I did that but i still have the same problem , please help

When you turn the key to the IGNITION position, does the Blue LED shut off??

And after doing the MASTER RESET,  you will NEED to reconnect the Evo All to the Flashlink-2 updater and make sure that options C1, D1 and D2 are toggled ON still and SAVE OPTIONS

The blue led didn't shut off , it is constant.

I did the master after that i enabled the c1 , d1 , d2.

what am facing if i reconnet the igition wire on the male / famale harness then it will will start blinking and the i response to the 3x buttons but it doesn't start the engine.

i know that i have to connect the yellow wire from the male harness to the yellow/green of the red 5 pin connector and the yellow that comes alone with the yellow in the 20 pin.
...